Getting Familiar with Plumbing: Before Installing a Bathtub
Getting Familiar with Plumbing: Before Installing a Bathtub
Blog Article
What're your opinions on A Step-by-Step Guide to Installing a Bathtub?
Mounting a tub isn't precisely brain surgery, but it does call for solid plumbing, woodworking, and also occasionally, tiling skills. Changing an old bathtub with a brand-new one is also a moderately tough project. If the old bathtub is easily easily accessible, the job can move rapidly; if you need to open a wall surface to get rid of the old bathtub and also place the brand-new bath tub, the task is a lot harder. In either situation, the task is within a house handyman's abilities, although you will require an assistant to leave the old bathtub as well as set in the brand-new one. Make sure you have actually certified yourself for the job and are comfortable attempting it. Instead of hiring a contractor to take control of a halfway-completed task, it is much better to take into consideration using one prior to you start. Possibilities are you may need a specialist plumber to make tube links.
This article will certainly assist you mount a brand-new tub in your bathroom if you have actually currently acquired a brand-new tub and also don't need to transform the setup of your previous supply of water pipelines.
Your devices and material list should make up the following:
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your setup, after that the first thing you must do is detach the water. After doing so, switch on the taps to drain pipes any kind of water staying in the system. The procedure of removing the existing faucets can be quite troublesome because of the limited accessibility that is frequently the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipes to the faucets. Have a towel ready for the staying water that will originate from the pipes. As soon as the supply pipelines have actually been gotten rid of, use the very same device to loosen the nut that holds the faucets onto the bath/basin. You will need to stop the single taps from turning during this process. When the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleaned up of any type of old securing substance.
Before carrying on to fit the brand-new taps, compare the pipe connections on the old faucets to the new faucets. If the old faucets are longer than the new taps, then a shank adapter is required for the brand-new taps to fit.
Suitable New Touches
If the tails of the new faucets are plastic, after that you will require a plastic port to stop damages to the string. One end of the port fits on the plastic tail of the faucet as well as the various other end provides a link to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly require minimizing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next, position the faucet in the mounting opening in the bath/basin guaranteeing that the washing machines remain in place between the faucet and also the sink. Secure the faucet in position with the maker given backnut. Once the tap is securely in place, the supply pipelines can be attached to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with normal faucet ports. The previous kind ought to be attached to the faucet finishes first, tightening up only by hand. The supply pipelines can later be connected to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Installing the Bathtub
Utilizing both wood boards under its feet, position the bathtub in the called for setting. The wooden boards are helpful in uniformly spreading out the weight of the tub over the location of the boards rather than focusing all the weight onto 4 tiny factors.
The next objective is to make sure that the bath tub is leveled all round. This can be attained by examining the spirit level and changing the feet on the tub until the spirit level reviews level.
To set up faucets, fit the bottom of the furthest versatile tap connector to the ideal supply pipe by making a compression sign up with; after that do the exact same for the various other tap.
Turn on the water as well as check all joints as well as new pipework for leakages and tighten them if required. Load the bath tub as well as additionally inspect the overflow electrical outlet and the regular electrical outlet for leakages.
Finally, fix the bathroom paneling as explained in the producer's instruction manual. Tiling and securing around the tub ought to wait till the bath tub has actually been made use of at least when as this will certainly settle it right into its last placement.
Planning for the Installation
To start with, the supporting framework provided with the bath ought to be fitted (if called for) according to the maker's guidelines. Next off, fit the faucets or mixer to the tub. When suitable the tap block, it is necessary to make sure that if the faucet includes a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the taps device to avoid stress on the bath tub.
Fit the versatile faucet connectors to the bottom of the two taps making use of 2 nuts and also olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bathroom. Use the nut supplied by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bathroom. Ensure you make use of every one of the provided washing machines.
Connect the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath must now be ready to be fitted in its final position.
Tiling Around the Bathtub
In the location where the bathroom fulfills the tile, it is required to seal the joins with a silicone rubber caulking. This is essential as the fitting can relocate sufficient to split a stiff seal, causing the water to pass through the wall in between the bath as well as the tiling, bring about complications with wetness and also feasible leakages to the ceiling below.
You can choose from a range of coloured sealers to assimilate your components and installations. They are sold in tubes as well as cartridges, and can sealing voids as much as a width of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with spins of drenched paper or soft rope. Keep in mind to constantly fill up the bathtub with water before sealing, to permit the activity experienced when the bathtub is in use. The sealer can break fairly very early if you do not take into account this movement prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also easily readily available on the market. It is advisable to fit the ceramic tiles utilizing waterproof or waterproof adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I discovered that blog entry about A Step-by-Step Guide to Installing a Bathtub when doing a lookup on the search engines. Sharing is nice. Helping others is fun. Thank you so much for your time invested reading it.
Request expert assessment. Report this page